Leakoo
ArtisanGuild from patreon
ArtisanGuild patreon

Flokir the Skald freebie

🕑 Added 2020-06-19 20:01:29 +0000 UTC
Flokir the Skald freebie

Comments

Jake Coulson

Hey where did this guy go? Can't find him on Thingiverse anymore other than one of his weapons :(

Dwayne Spencer

I finally got to print this guy. can i still get the updated file for the horn and axe bow? both failed.

Fogo

I am having the same issues with bow and horn, despite multiple attempts to increase exposure time and reduce lift speed. I can't help but to feel that the supports are too light as the supports in some of your more recent supports appear to be heavier.

Artisan Guild

thank you so much! We will updload an updated version shortly

Richard Vaughan

I have attempted printing the pre-supported version of this model 3 times now and the bow and horn rip off the supports each time. I think there are not enough bulky supports. I am getting a 100% fail with the models ripped off the light support. I am going to attempt to add in some bulkier supports and see what happens.

Artisan Guild

yes, he will be part of the Dwarven presupported Set :)

Vinnie Simonetti

Oh snap, it's been more then a week. I didn't think I had this tab open that long... I'm assuming that this will be released as part of a full Dwarven pre-supported set eventually? (just checking, as I may just wait until then to update everything at once)

Artisan Guild

Yes, the axebow supports had been updated :)

Edric Ivan

Just wondering if the supports were updated since last upload? :)

Renato Tarabella

yes Patrick, Andrea told me that. I've implemented now thick supports that guranteed that all will not detach. I'm still learning from my experience with photon S.

Patrick Krog

You should probably know, a lot of people print these models at 90% instead of full scale, some even 85%. So the supports should be big enough that they retain their effectiveness when scaled down. Greg does a really good job of this, and he has a new video on making Light supports work better. If you haven't seen his videos i highly recommend them. I printed out this guy at 90%, and though I didn't have anything fail, i noticed the supports as they were originally were not printing in some places when it was scaled down as i normally do.

Renato Tarabella

Please get it here: https://www.thingiverse.com/thing:4490437

Renato Tarabella

Hi Gingerfreak, i'll support again the crossbow with bigger supports. We'll update Thingverse with it.

MikaWell

Same here, 2 crossbow : one is hanging on only one support, the other is in the VAT... (printed on 0.025).Anyway, thank a lot for the effort :)

I can't get the supported crossbow to print :/ supports a breaking :( the rest is printing fine.

Renato Tarabella

Hi Ibas, seem a deleted part of support. Chitubox, sometime, leave there polygon parts of deleted support... there are some bugs in this software.

Great model! Any chance to get chitubox files for him? There are minor errors in supports, for example around 82 and 83 layer (on 0.05) there are some floating supports in the air.

Brian Bartley

more dwarves! thanks!

Caesarion

Amazing, thank you

Sean McInnes

Thank you for your amazing effort!!

J-Zarno .

Every set after that one has supported bases

Richard Wall

Are the bases going to be pre-supported? I noticed none of the dwarves in the Oathbreakers set have their bases supported.

Thomas Klein

Modular horn too. Time to make some full command squads

Whiskeyjack

New book and cape woosh nice!

R Boz

Continuing to amaze. Thank you!

Yoann

Merci !!

I love it!

Matthieu Rousselin

Thx a lot !

Nate

Nice job on the supports Renato! We all appreciate your hard work


More Creators